Saudi-Arabia-Flag Iran-Flag-icon United-Kingdom-flag-icon

Specification polyethylene line pipe

Specification for Polyethylene Line Pipe

 

This document was produced under API standardization procedures that ensure appropriate notification Specification polyethylene PipeLine and participation in the developmental process and is designated as an API standard.
Questions concerning the interpretation of the content of this publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards, American Petroleum Institute, 1220 L Street, N.W., Washington, D.C. 20005. Requests for permission to reproduce or translate all or any part of the material published herein should also be addressed to the director.

Scope

Purpose
The purpose of this specification is to provide standards for polyethylene (PE) line pipe suitable for use in conveying oil, gas and non-potable water in underground, above ground and reliner applications for the oil and gas producing industries.
The standard does not propose to address all of the safety concerns associated with the design, installation or use of products suggested herein. It is the responsibility of the user of the standard to utilize appropriate health and safety considerations.
All pipe produced under this standard must utilize pressure rated materials, but may be used in pressurized, nonpressure and negative pressure applications.
The technical content of this document provides requirements and guidelines for performance, design, materials inspection, dimensions and tolerances, marking, handling, storing and shipping.

Applications

Specification polyethylene PipeLine

Equipment

This specification covers polyethylene line pipe utilized for the production and transportation of oil, gas and nonpotable water. The piping is intended for use in new construction, insertion renewal, line extension and repair, of both above ground and buried pipe applications. Specific equipment covered by this specification is listed as follows:

  1. polyethylene pipe ;
  2. polyethylene fittings .

Service Conditions

The standard service conditions for the API Spec15LE Standard Pressure Rating are as follows:

      1. HDB is established to 50 years;
      2. service temperature is between –30 °F and 140 °F;
      3. the fluid environment is oil, gas and non-potable water;
      4. axial loads shall include end loads due to pressure only.

Service conditions other than the standard API Spec 15LE conditions are discussed in Section 5—Design.

Unit Conversion
A decimal/inch system is the standard for the dimensions shown in this specification. Nominal sizes will continue to be shown as fractions. For the purposes of this specification, the fractions and their decimal equivalents are equal and interchangeable. For SI metric unit equivalents in millimeters (mm), multiply by 25.4 and round to 1 decimal place.
Basic metric conversions are described in Annex A.

Requirements
Requirements of other standards included by reference in this specification are essential to the safety and interchangeability of the equipment produced.

Equivalent Standards
Standards referenced in this specification may be replaced by other international or national standards that can be shown to meet or exceed the requirements of the referenced standard. Manufacturers who use other standards in lieu of standards referenced herein are responsible for documenting the equivalency of the standards. Where a standard is revised, the latest edition may be used on issue and shall become mandatory 6 months from the date of the revision.

Download the full text of Specification for Polyethylene Line Pipe (PE) »

API SPECIFICATION 15LE
FOURTH EDITION, JANUARY 2008
EFFECTIVE DATE: JULY 2008 

برترین مطلب

لوله های پلی اتیلن HDPE

كاربري لوله‌های پلی اتیلن انتقال آب، مواد شيميائي، سيالات خنك كننده و گرم كننده، مواد غذائي، دوغابها، گازها، هواي فشرده و سيستمهاي خلأ، چه در روي زمين و چه در زير زمين است. آغاز استفاده از لوله هاي پلاستيكي تحت فشار، از حدود سال 1950 ميلادي بود. 

 « Specification for Polyethylene Line Pipe •
« هندبوک لوله پلی اتیلن / Hand Book of Polyethylene Pipe •
« Standard for Polyethylene Pipe & Fittings for Underground Fire Protection •